Fig. 11.5. Installation of mudguards, longerons and panel of facing of a radiator: A1 = 1260 mm; A2 = 1547 mm; A3 =810 mm

Fig. 11.6. Control amount of installation of the panel of facing of a radiator and basic cups of springs of a forward suspension bracket: A4 = 840 mm; A5 = 990 mm

Fig. 11.7. The control size allowing to determine the shift of basic cups of springs of a forward suspension bracket: A6 = 1220 mm

Fig. 11.8. Control amount of installation of longerons and cross-piece of podkapotny space: B1 = 660 mm; B2 = 955 mm

Fig. 11.9. Measurement of an aperture of a windshield: C1 = 1365 mm

Fig. 11.10. Control size of a forward aperture and relative provision of forward and average racks of a body: D1 = 1085 mm

Fig. 11.11. The sizes allowing to estimate change of geometry of a forward doorway: D2 = 1325 mm; D3 = 857 mm

Fig. 11.12. The sizes allowing to estimate change of geometry of a back doorway for a body "sedan": D4 = 1040 mm; D5 = 840 mm

Fig. 11.13. The size defining relative position of average and back is resistant, for a body "sedan": D6 = 876 mm

Fig. 11.14. The sizes allowing to estimate change of geometry of a back doorway for a body "station wagon": D7 = 1088 mm; D8 = 840 mm

Fig. 11.15. The size defining relative position of average and back is resistant, for a body "station wagon": D9 = 875 mm

Fig. 11.16. The sizes defining the relative provision of average racks of a body: E1 = 1550 mm; E2 = 1370 mm; E3 = 1390 mm

In fig. 11.5,11.6,11.7 the control amount of installation of body details in podkapotny space is presented. The control sizes of the lower part of podkapotny space are given in fig. 11.8. The control size of an aperture of a windshield is given in fig. 11.9. Apertures of forward doors on bodies "sedan" and "station wagon" are identical. Their control sizes are shown нарис. 11:10 and 11.11. Apertures of back doors for bodies "sedan" and "station wagon" differ. Their sizes are given in fig. 11.12,11.13,11.14,11.15.

Fig. 11.17. Points of application of the measuring tool

Fig. 11.18. Scheme of measurement of an aperture of back glass: F1 = 1245 mm

Fig. 11.19. Points of application of the measuring tool at measurement of diagonals of an aperture of back glass

Fig. 11.20. Control sizes of a back cross-piece of a luggage compartment and top back part of an aperture of a trunk lid: G1 = 1240 mm; G2 = 975 mm

Fig. 11.21. The trunk lid aperture size in the lower part: G3 = 870 mm

Fig. 11.22. The control sizes of an aperture under the fifth door of a body "station wagon": H1 = 1015 mm; H2 = 1116 mm

Fig. 11.23. The control sizes of provision of sidewalls of a body on an aperture of the fifth door of a body "station wagon"

Fig. 11.24. Control sizes of longerons of a back of bodies "sedan" and "station wagon": J1 = 1145 mm; J2 = 1670 mm; J3 = 885 mm

Fig. 11.25. Relative sizes of provision of forward and back longerons of a floor: K1 = 1767 mm

Fig. 11.26. General control size of the bottom of a body: L = 4049 mm

In case of need repair of consequences of side blow or capsizing the sizes between average racks of a body presented in fig. 11.16 and fig. 11.17 which are identical to bodies "sedan" and "station wagon" are important. These sizes allow to estimate change of geometry of salon. The aperture of back glass is controlled by measurement of the diagonals shown in fig. 11.18 and 11.19. The sizes of a luggage compartment and aperture of a trunk lid for a body "sedan" are given in fig. 11.20 and 11.21, and for the fifth door of a body "station wagon" in fig. 11.22 and 11.23. The sizes of a lonzheronny part of a back of a body given on fig. 11.24 are identical to "sedans" and "station wagons". The relative amount of installation of forward and back longerons for bodies "sedan" and "station wagon" is identical and presented in fig. 11.25. The general control size of the bottom "sedan" and "station wagon" is identical to bodies and is measured between an extreme opening of a forward cross-piece and the end of a back longeron, as shown in fig. 11.26.